Mon-Fri, 9am-5pm EST
GET $7 OFF
*Special coupons will be sent in monthly newsletters
Adults: The weight of the ball should be roughly ten percent of your body weight. Another good rule to go by is to choose a ball that is one to two pounds heavier than the house ball you are bowling with. The reason being is that the grip on the house ball is incorrect and a custom fit ball will feel much lighter because it will be easier to hold on to.Kids: We recommend a weight equal to their age. Please note 6 & 8 lb bowling balls are designed for kids only not adults. Some manuacturers will not warranty 6 & 8 lb balls that are drilled for adults.
Top weight is the amount of weight difference from the top of the bowling ball (CG) and the bottom of the ball (opposite the cg).
In general their will always be more weight to the top of the ball (CG). This is due to the fact that when you drill finger holes into the ball you are extracting weight from the ball (generally 2 ounces or more depending the hole sizes and the density of the core) and it was initially designed to keep the ball balanced after it was drilled.
Balls with lower initial top weight were generally more stable after drilled than those with higher top weights due to the fact that their was so much weight left over after drilling. This created imbalance and often time added length and backend reaction for early three piece (Pancake weight block) bowling balls.
Top weight by today's standards is not nearly as important because a majority of the weight mass of most bowling balls is closer to the center of the ball than the shell and top weight has less of an effect because ball motion is more about the placement of the weight block itself and not the static weight mass. Top weight these days usually dictates hole size for those off label drillings.
What does this mean in selecting the correct top weight?
2.5 or less - Is for standard drilling techniques. It is also used for advanced drillings where moving the cg further off center of span creates a stronger drilling. You may not needing a weight hole with this type of drilling but depending on how far the cg is moved you may need a weight hole.
2.5 to 3.5 - Is great for normal layouts, a weight hole is not typical for this top weight. Stronger drillings may require a weight hole.3.5 or more - This top weight is good if you want the ball to push more (go farther down the lane) while adding backend motion, but only if the ball driller knows and incorporates this into the drilling.
It can also be used for placing a big weight hole in a ball because it adds static weight to the drilling. This means you can use a stronger drilling than normal but make it legal by adding a weight hole to remove excess top weight (you can only have 1 oz of top weight remaining after drilling).
***NOTE: These are just basic descriptions to what top weight can do. There are many more scenarios for each top weight and what is capable with each different top weight range. Please discuss with your ball driller how they plan to drill you ball to get a better idea if they plan to use a weight hole or not to achieve the ball reaction you desire. There is no way to guarantee a ball will not need a weight hole depending on the top weight selected, the ball layout will determine that.
If your new ball cracks while being drilled by a pro shop, CheapBowlingBalls.com will replace your ball free of charge! Manufacturers' warranties typically do not cover for cracking during drilling and drillers are not held responsible for their mistakes or defects in the ball.
*Ball must be purchased from CheapBowlingBalls.com *Ball must be drilled within 11 days of receiving it (Extended to Feb 1, for purchases made between Black Friday and Christmas) *Protection must be purchased before the ball is drilled *Ball pictures must be sent for inspection and the receipt for drilling charges included also *We pay shipping back to you
Valid for 2 full years from date of purchase. Covers manufacturing defects of balls, bags & shoes.This warranty does not cover incidental costs of replacement including, but not limited to; freight, measuring, and drilling.
Shoe Size Charts 900 Global, Brunswick, Dexter and Storm bowling shoes run true to size.Right Handed Shoes: Made for bowlers that bowl with their right hand because the slide pad is on the left shoe, which is the foot you slide with.Left Handed Shoes: Made for bowlers that bowl with their left hand because the slide pad is on the right shoe, which is the foot you slide with.Uni-sole Shoes: These shoes can be used for right or left handed bowlers because the slide pads are on both feet.
Don't know your shoe size? Do the following...To get the best fit and comfort, we suggest measuring your feet each time you purchase a new pair of shoes because your feet will change during your lifetime. 1. Get a blank piece of paper, a pencil and a ruler or tape measure.2. Put on the pair of socks you intend to wear with the shoes you are ordering. Through the course of the day, your feet will swell so it's best to measure them at the end of the day.3. With the paper placed on a hard floor, sit down in a chair and place your foot flat on the paper. Lean forward, putting more weight onto the foot you are going to measure. As you probably know, your feet are different sizes so be sure to measure your larger foot.4. Holding a pencil vertically, place a mark at the end of your heel. Place another mark at the tip of your longest toe.5. With the ruler or tape measure, measure from the heel to the tip of your longest toe.
To Find Your Width:Measure the distance between the two widest points on your foot. Reduce this number by 5 mm, or 1/5-inch. The result is the number you will use to determine your foot width.To find your size, use the inch-to-size table. For example, if you are a man and your foot measures 10" long, you will wear a U.S. size 8 shoe. If you are between measurements, size up to the next larger size. It is easy to add a pair of socks to take up a little extra room but very difficult to make shoes that are too small comfortable.Note: Just because you are a size 9 in one brand doesn't necessarily mean you are going to be a 9 in another. Footwear sizes and shapes vary from brand to brand. Please keep this in mind.
( Men's ) Sizing Chart
Heel to toeLength(in inches)
Heel to toeLength(in Cm.)
Narrow Width(B or C) forthis Size
Medium Width(D) forthis Size
Extra Wide Width(2E or 3E) forthis Size
( Women's ) Sizing Chart
Narrow Width(AA) forthis Size
Medium Width(B) forthis Size
Wide Width(D) forthis Size
Extra WideWidth (EE)for this Size
( Kids' - boys & girls ) Sizing Chart
If customer selects UPS for original shipping, CheapBowlingBalls.com will send you one UPS return label to get the shoes that do not fit back to us, and for the correct shoe size to be resent back to you one time only.If customer selects USPS for original shipping, the customer will be responsible to ship the shoes back to us using USPS Standard Post and we will credit the amount of shipping back to you. CheapBowlingBalls.com will then send the correct shoe size back to you one time only using USPS Standard Post.The shoe size protection plan must be purchased at the same time as the shoes. If ordering multiple pairs of shoes only the pair(s) which purchased the shoe size protection will be honored.Shoe Size Protection Plan is valid only for the same model shoe you purchased just in a different size. You may not switch shoe models.Valid only in the Continental US.
If you loved Ebonite's V2 core, you're going to thank your lucky stars for the new Gamebreaker! Utilizing this signature core from Ebonite, the Gamebreaker takes the V2 core to the next level by wrapping it in one of the company's most successful veneers, the GB 10.7 (otherwise found on The One), making this ball perform like a V2 on steroids. The result is a match made in heaven.
Hours of Operation: Mon-Fri, 9am-5pm EST
© Copyright 2004 - 2015 CheapBowlingBalls.com All Rights Reserved.CheapBowlingBalls.com 3204 Woodman Dr. Kettering, OH 45420